Electromagnetic Dosing Feeders for Controlled Material Flow
Deliver suitable powders, granules and small bulk materials into your process with an electromagnetic dosing feeder designed around your application. At Spiral Elevator, we design and manufacture bespoke feeding equipment in the UK for controlled supply to weighing, batching, mixing and packaging operations.
Our magnetic dosing feeders combine a conveying tray, electromagnetic drive and compatible controller. We assess these components together with your material, hopper arrangement and required operating range to develop a practical feeding solution.
Controlled Feeding for Batching and Packaging
A production process may require a steady stream of material, repeated small doses or a rapid initial fill followed by a slower finishing stage. Each duty places different demands on the feeder and its controls.
Electromagnetic dosing feeders can be assessed where responsive adjustment of material delivery is important. The arrangement should provide useful control across the required feed range, including the lowest rate needed near the end of a batch.
We start with the result you need: how much material must be delivered, how quickly it must arrive and what variation is acceptable. These requirements guide the tray design, drive selection and control sequence.
How an Electromagnetic Vibratory Feeder Works
An electromagnetic drive creates movement through a spring-supported tray. This motion advances suitable material towards the discharge, while a compatible controller adjusts the drive output to regulate feeding.
The word “magnetic” describes the drive mechanism. The material being conveyed does not need to be magnetic.
The drive, springs and tray form a coordinated assembly. Their selection must account for the tray weight, product load and required conveying behaviour. The controller must also match the specified drive and electrical supply.
Powder and Granule Dosing Equipment
Material behaviour has a direct effect on dosing performance. Free-flowing granules may form a predictable stream, while cohesive powders can stick, bridge or change flow characteristics as their moisture content varies.
We review bulk density, particle size, temperature and any tendency to compact or segregate. For fragile products, the tray surface and transfer points also need consideration.
The smallest required dose can be as important as maximum throughput. Where the material is difficult to handle or the tolerance is demanding, representative trials can help assess the achievable feeding range and repeatability.
Integrating Feeders with Weighing Systems
Controlling material flow and measuring the quantity delivered are separate functions. An electromagnetic feeder regulates delivery, while a weighing system provides the measurement needed for a specified batch weight or mass flow.
A batch process may use a higher feed rate for the initial fill, followed by a slower rate as the target weight approaches. The final result also depends on the weighing response and material still falling after the stop signal.
We assess batch size, acceptable tolerance, cycle time and discharge height together. This helps establish a feeding and weighing sequence suited to the actual product rather than relying on the controller setting alone.
Consistent Supply from the Hopper
A dosing feeder needs a suitable supply of material at its inlet. Hopper outlet size, clearance above the tray and changing material pressure can all affect the feeding behaviour.
A feeder that performs well with a shallow layer may respond differently beneath a full hopper. We therefore consider the hopper and tray as an interacting system, including how the hopper is refilled during production.
Where material struggles to leave storage, a vibratory hopper discharge system may be worth assessing. Its role is to support material release, while the dosing feeder regulates onward delivery.
Connecting to Your Production Process
An electromagnetic dosing feeder can supply a weighing hopper, mixer, packaging machine or another suitable process stage. The discharge position and control signals should match the receiving equipment.
For vibrating screens, controlled feeding can help manage the incoming load and material distribution. Where the main requirement is general bulk transfer, our wider range of vibrating feeders provides further options for assessment.
If product protection or control of material escape is a priority, we can also review whether an enclosed tube feeder would better suit the transfer duty.
Cleaning Access and Product Changeovers
The feeder should suit how your team cleans and operates the production line. Tray construction, contact surfaces and access need to reflect the product, cleaning method and frequency of changeovers.
Where several ingredients share the same equipment, retained material and carryover between batches deserve particular attention. We discuss these requirements during specification so inspection and cleaning can be planned into the arrangement.
Available working space also matters. Operators need practical access to the tray, hopper interface and drive components without surrounding equipment obstructing routine tasks.
Discuss Your Electromagnetic Dosing Requirements
Send us your material details and the feeding result you need so we can assess a suitable arrangement.
Useful information includes:
- Material type, bulk density and particle-size range
- Moisture content and operating temperature
- Minimum, normal and maximum feed rates
- Target batch weight and acceptable tolerance
- Required cycle time
- Hopper dimensions and refill method
- Existing weighing equipment and control signals
- Available installation space and discharge height
- Cleaning and product changeover requirements
Our team can review your application and develop an electromagnetic dosing feeder proposal around your product, controls and production requirements.
Email sales@spiralelevator.com or call 0800 001 6520 to discuss your dosing feeder project.


